Phineas
From FamiLAB Wiki
(Difference between revisions)
(→Notes) |
|||
| (One intermediate revision by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | I'll work to keep this current, feel free to email / call with questions... | |
__NOTOC__ | __NOTOC__ | ||
| Line 30: | Line 30: | ||
===Electronics=== | ===Electronics=== | ||
| − | * RAMPS | + | * RAMPS v1.2 |
| − | * | + | * Polulus |
| − | * Fan for Polulu | + | * Fan for Polulu - 40mm(?) from Skycraft |
| − | * Power Supply | + | * Arduino Mega 2560 |
| − | + | * Power Supply - Sunpower Model FDPS-240A 12v 20A power supply | |
| + | |||
===Mechanical=== | ===Mechanical=== | ||
| − | + | * Makergear Prusa Mendel Hybrid Kit | |
| + | * Makergear stepper extruder | ||
| + | * 0.9 degree steppers on X & Y (with shafts flattened for pulley set screws) | ||
| + | * 1.8 degree steppers on Z (qty 2) | ||
| + | * Swapped out ceramic heater (kept breaking them) for Resistor Block | ||
| + | * .35 nozzle | ||
| + | * Moved X endstop so that origin (0,0) is front left (with Y stepper at the BACK) | ||
| + | |||
===Software=== | ===Software=== | ||
Ian (user link) is currently using the following: | Ian (user link) is currently using the following: | ||
| − | * | + | * Pronterface with SFACT |
| − | * | + | * [https://picasaweb.google.com/lh/photo/TirTcg47PfZAf2lZk6cUPw?feat=directlink 10/2/2011 CURRENT SCREENSHOT OF SETTINGS] |
| + | |||
===Print Status=== | ===Print Status=== | ||
| − | The printer is | + | The printer is NOW printing. It needs better calibration, but it is close. |
| + | |||
==Current Work== | ==Current Work== | ||
| + | This is the TODO or In-progress list... | ||
===Electronics=== | ===Electronics=== | ||
| − | * Get the fan on the polulus | + | * Get the fan on the polulus mounted & connected to always be on |
| + | * Build a RAMPS case | ||
| + | * Clean up stepper wiring, and add some nice disconnects... | ||
===Mechanical=== | ===Mechanical=== | ||
| − | * | + | * Add a print cooling fan? |
| − | + | ||
===Software=== | ===Software=== | ||
| − | * | + | * Speed up python? |
| − | + | ||
===Notes=== | ===Notes=== | ||
* Turn on & off fan in D9 with M106 | * Turn on & off fan in D9 with M106 | ||
* [http://reprapfordummies.net/index.php?option=com_content&view=article&id=49:sfact-homepage&catid=44:gcode-generators&Itemid=66 Calibrating SFACT - DO THIS] | * [http://reprapfordummies.net/index.php?option=com_content&view=article&id=49:sfact-homepage&catid=44:gcode-generators&Itemid=66 Calibrating SFACT - DO THIS] | ||
| + | * Spent lots of time getting bind out of the Y & Z - this is why the Polulus needed so much current, and why they were overheating... | ||
Latest revision as of 14:33, 2 October 2011
I'll work to keep this current, feel free to email / call with questions...
Information
Pic goes here
Link to raising geeks goes here
General
Phineas (nickname) is a RepRap Prusa Mendel, built from a MakerGear Prusa Mendel Kit.
It was purchased and built by Ian (Digitalman2112) between April and June of 2011.
Photos
Warning, I make mistakes, and sometimes the mistakes stay in the photos - don't use these as your only reference :)
Build Photos - Heated Build Platform
Documentation
MakerGear Prusa Build Instructions - These are a complement to the Visual Prusa Instructions
Electronics
- RAMPS v1.2
- Polulus
- Fan for Polulu - 40mm(?) from Skycraft
- Arduino Mega 2560
- Power Supply - Sunpower Model FDPS-240A 12v 20A power supply
Mechanical
- Makergear Prusa Mendel Hybrid Kit
- Makergear stepper extruder
- 0.9 degree steppers on X & Y (with shafts flattened for pulley set screws)
- 1.8 degree steppers on Z (qty 2)
- Swapped out ceramic heater (kept breaking them) for Resistor Block
- .35 nozzle
- Moved X endstop so that origin (0,0) is front left (with Y stepper at the BACK)
Software
Ian (user link) is currently using the following:
- Pronterface with SFACT
- 10/2/2011 CURRENT SCREENSHOT OF SETTINGS
Print Status
The printer is NOW printing. It needs better calibration, but it is close.
Current Work
This is the TODO or In-progress list...
Electronics
- Get the fan on the polulus mounted & connected to always be on
- Build a RAMPS case
- Clean up stepper wiring, and add some nice disconnects...
Mechanical
- Add a print cooling fan?
Software
- Speed up python?
Notes
- Turn on & off fan in D9 with M106
- Calibrating SFACT - DO THIS
- Spent lots of time getting bind out of the Y & Z - this is why the Polulus needed so much current, and why they were overheating...
