Phineas
(Created page with "ACTIVELY BUILDING THIS PAGE FROM A COPY OF THE BREEPBROOP PAGE, WORK IN PROGRESS __NOTOC__ ==Information== Pic goes here Link to raising geeks goes here ===General=== Phineas...") |
|||
| Line 11: | Line 11: | ||
It was purchased and built by Ian ([[user:Digitalman2112|Digitalman2112]]) between April and June of 2011. | It was purchased and built by Ian ([[user:Digitalman2112|Digitalman2112]]) between April and June of 2011. | ||
| + | |||
| + | ===Photos=== | ||
| + | |||
| + | Warning, I make mistakes, and sometimes the mistakes stay in the photos - don't use these as your only reference :) | ||
| + | |||
| + | [https://picasaweb.google.com/ian.cole/MakerGearPrusaMendelKitBuild?authuser=0&feat=directlink Build Photos - Main Album] | ||
| + | |||
| + | [https://picasaweb.google.com/ian.cole/MakerGearPrusaMendelRAMPS?authuser=0&authkey=Gv1sRgCN_75cCLjsiTIw&feat=directlink Build Photos - RAMPS] | ||
| + | |||
| + | [https://picasaweb.google.com/ian.cole/MakerGearPrusaMendelEndstops?authuser=0&authkey=Gv1sRgCKGsisPe8ZuX1AE&feat=directlink Build Photos - End Stops] | ||
| + | |||
| + | [https://picasaweb.google.com/ian.cole/MakerGearPrusaMendelBuildPlatform?authuser=0&authkey=Gv1sRgCMWQ1b-1i5WmFA&feat=directlink Build Photos - Heated Build Platform] | ||
| + | |||
| + | |||
| + | ===Documentation=== | ||
| + | [https://docs.google.com/document/d/1yWRVPTOax8xDhF92GWmMOm8izQn5R2MJz1NYHC3MZUw/edit?hl=en_US&pli=1 MakerGear Prusa Build Instructions] - These are a complement to the [http://garyhodgson.com/reprap/prusa-mendel-visual-instructions/ Visual Prusa Instructions] | ||
| + | |||
===Electronics=== | ===Electronics=== | ||
Revision as of 15:20, 26 September 2011
ACTIVELY BUILDING THIS PAGE FROM A COPY OF THE BREEPBROOP PAGE, WORK IN PROGRESS
Information
Pic goes here
Link to raising geeks goes here
General
Phineas (nickname) is a RepRap Prusa Mendel, built from a MakerGear Prusa Mendel Kit.
It was purchased and built by Ian (Digitalman2112) between April and June of 2011.
Photos
Warning, I make mistakes, and sometimes the mistakes stay in the photos - don't use these as your only reference :)
Build Photos - Heated Build Platform
Documentation
MakerGear Prusa Build Instructions - These are a complement to the Visual Prusa Instructions
Electronics
- RAMPS
- Polulu
- Fan for Polulu
- Power Supply
- ???
Mechanical
No mods, yet. Note that Rick from Makergear prints with his X "backwards", so the X endstop needs to be reworked to be "correct"
Software
Ian (user link) is currently using the following:
- skeinforge link
- firmware TBD
Print Status
The printer is not printing. Ian hasn't been spending the needed time, had a bunch of self-inflicted heater core issues, and just generally hasn't worked through it...
Current Work
Electronics
- Get the fan on the polulus
Mechanical
- Flatten the stepper shafts and remount the X & Y pulleys
- Build and install new hotend
Software
- Select and install new firmware
